博文
- 分享 Lonsdor K518 Pro Vehicle Support List (Newest)
- LonsdorK518 PRO Key Programmer has built-inLKE, and supports Bluetooth, filemanagement, anti-theftdeactivation,accesscardcopy, dataWriteInitialization,EEPROMdatamileage restoration, CAN-FDProtocol DOIPProtocol. ...
- 分享 How to Solve Yanhua ACDP 2 Failed to Connect PC via USB Problem?
- If Yanhua Mini ACDP-2 fails to connect PC via USB cable and appears no device found problem, how to solve? Check the available solution below. Problem: Connect ACDP2 host to computer via USB cable Open PC-ACDP2 software and wait for dozens of seconds, but the device is still not c ...
- 分享 How to Read/Write Volvo CEM DELPHI 2015- R5F64525 with OBDSTAR DC706 on Bench?
- Volvo DELPHI 2015- R5F64525 CEM can be cloned with OBDSTAR DC706 in bench mode. Only 2 minutes! Preparation: Volvo DELPHI 2015- R5F64525 CEM OBDSTAR P004 ECU Clone Jumper OBDSTAR P004 Adapter 12V2A charger OBDSTAR main cable (OBD cable) OBDSTAR DC706 ECU Tool How to do ...
- 分享 OBDSTAR DC706 Read Ford Lear MC9S12XEP768 BCM Failure Solution
- Problem: OBDSTAR DC706 ECU Tool failed to read Ford Lear MC9S12XEP768 BCM on bench. DC706 cannot get it to communicate with the Ford Lear BCM, and neither does V2 black housing. The solution: Please try to solve this problem with the following methods. Method 1: T ...
- 分享 How to Clone BMW MSV90 Engine Computer with Launch X431 ECU Programmer?
- Confirmed! BMW MSV90 TC1796 engine computer can be cloned with Launch X431 ECU TCU Programmer successfully, no need X431 tablet and X431 X-Prog3 programmer . Main steps: Step 1: Read EEPROM and Flash data of original engine computer Step 2: Read EEPROM and Flash data of new engi ...
- 分享 Foxflash ECU Bench Box Do Self-Test Guide
- Foxflash bench box works with OBD and direct connect bench. If the bench box doesn’t have a connection, how to do a self-test? Here is the simple operation guide. 1.Connect Foxflash tool and a computer via the USB cable Connect the Bench Box to foxflash ECU programmer and power it t ...
- 分享 CGDI “Software is Unauthorized” Error Solution
- Recently, some customers gave feedback that CGDI device ( CGDI MB , CG100 / CG100X , CG FC-200 …) had subscription update problem. They purchased the update service, but the software prompted “Software is unauthorized and cannot be used…”. Here is the solution: The main cause i ...
- 分享 Launch X431 Tablet Calibrate Mitsubishi Triton 2019 Steering Angle Sensor Tutori
- How to use Launch X431 Scanner (such as X431 V , V+ , PAD VII , PRO5 , X431 IMMO Plus , IMMO Elite , X431 PROS V1.0 , PRO3S+ Pro3 , etc. ) to do SAS (Steering Angle Sensor) calibration on 2019 Mitsubishi Triton? Check the operation guide below. i.e. X431 PAD V Make sure the conn ...
- 分享 2023 Lonsdor K518 Pro vs. Lonsdor K518ISE/K518S
- Lonsdor K518 Pro is the upgraded version of K518 . What’s the difference between them? What is new in K518 Pro? Let’s check the comparison table. Item Lonsdor K518Pro Lonsdor K518ISE / K518S Remarks Image Operation system Android 9 - &nbs ...
- 分享 How to Generate BMW FEM/BDC key with CGDI BMW Pro and Godiag FEM/BDC Test Platfo
- Generate FEM/BDC key with CGDI BMW Pro and Godiag FEM/BDC Test Platform on bench. Step 1: Connect device Connect CGDI Prog BMW MSV80 key programmer to computer via USB cable, and connect to Godiag BMW FEM/BDC Test Platform via OBD cable Connect Godiag Test Platform to FEM/BDC module Supp ...
